Husqvarna 445 445e 450e Chainsaw Owners Manual, 2005,2006,2007,2008,2009

Operator’s manual (EPA III) Manuel d’utilisation (EPA III) Manual de instrucciones (EPA III) 445 445e 450e Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Lire attentivement et bien assimiler le manuel d’utilisation avant d’utiliser la machine. Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar la máquina. English (2-43) French (44-87) Spanish (88-129) 115 13 81-49 Rev.1 2009-02-13 KEY TO SYMBOLS Symbols on the machine: WARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others.

Chain Saw User Manual Free Download. Chainsaw Operator’s Manual. Chains for Chainsaws Free Instruction Manual Download PDF. Revision: 2005, 2006, 2007, 2008, 2009.

Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: · Approved protective helmet · Approved hearing protection · Protective goggles or a visor Both of the operators hands must be used to operate the chain saw. Symbols in the operator’s manual: Switch off the engine before carrying out any checks or maintenance. CAUTION! The start/stop switch automatically returns to run position. In order to prevent unintentional starting, the spark plug cap must be removed from the spark plug when assembling, checking and/or performing maintenance. Always wear approved protective gloves. Regular cleaning is required. Never operate a chain saw holding it with one hand only. Contact of the guide bar tip with any object must be avoided. Visual check. WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator. May cause serious personal injury. Recommended cutting equipment in this example: – Bar length: 16 inches – Max. nose radius: 10 Teeth – Chain type: Husqvarna H30 Other approved bar and chain combinations in Operator’s Manual. Protective goggles or a visor must be worn. Refuelling. Filling with oil and adjusting oil flow. Measured maximum kickback value without triggering the brake, for the bar and chain combination on the label. Other symbols/decals on the machine refer to special certification requirements for certain markets. The chain brake must be engaged when the chain saw is started. WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator. May cause serious personal injury. 2 ­ English 115 13 81-49 Rev.1 2009-02-13 KEY TO SYMBOLS You will find the following labels on your chain saw: EPA III USA Canada 39° The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements. Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual. The engine exhaust from this product contains chemical known to the State of California to cause cancer, birth defects or other reproductive harm. 115 13 81-49 Rev.1 2009-02-13 English ­ 3 CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: Symbols in the operator’s manual: CONTENTS Contents . INTRODUCTION Dear customer! . WHAT IS WHAT? What is what on the chain saw? . GENERAL SAFETY PRECAUTIONS Before using a new chain saw Important Always use common sense Personal protective equipment . Machines safety equipment . Cutting equipment . ASSEMBLY Fitting the bar and chain . FUEL HANDLING Fuel . Fueling Fuel safety STARTING AND STOPPING Starting and stopping WORKING TECHNIQUES Before use: General working instructions How to avoid kickback . MAINTENANCE General . Carburetor adjustment Checking, maintaining and servicing chain saw safety equipment Muffler . Starter . Air filter Spark plug . Lubricating the bar tip sprocket . Needle bearing lubrication Cooling system . “Air Injection ” centrifugal cleaning . Winter use . Maintenance schedule TECHNICAL DATA Technical data . Bar and chain combinations . Saw chain filing and file gauges.

Wikipedia’s page for Husqvarna

Publisher: www.husqvarna.com