Carrier 58ZAV 5SI Gas Furnace Owners Owners Manual - English

Weathermaker 8000TM 58ZAV Downflow/Horizontal Induced-Combustion Furnaces Installation, Start-Up, and Operating Instructions Sizes 050-135, Series 121 NOTE: Read the entire instruction manual before starting the installation. This symbol indicates a change since the last issue. Index Page ® ama CANADIAN GAS ASSOCIATION A PP R O VED R SAFETY CONSIDERATIONS 1-2 Clearances From Combustible Materials .1 Dimensional Drawing .2 ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS PROCEDURE 2-3 INTRODUCTION 3 LOCATION 3 General 3 Location Relative to Cooling Equipment 3 Hazardous Locations .3 AIR FOR COMBUSTION AND VENTILATION .3-5 Unconfined Space .4 Confined Space 4-5 SUPPLY-AIR PLENUM INSTALLATION (DOWNFLOW) 5-6 Installation On a Concrete Slab .5 Installation On a Combustible Floor 5-6 HORIZONTAL ATTIC INSTALLATION .6 Construct a Working Platform .6 Install Furnace .6 HORIZONTAL CRAWLSPACE INSTALLATION 6 FILTER ARRANGEMENT .6-7 GAS PIPING .7-8 ELECTRICAL CONNECTIONS 8 115-v Wiring .8 24-v Wiring .8 Accessories 8 VENTING .8-10 START-UP, ADJUSTMENT, AND SAFETY CHECK .10-15 General 10 Sequence Of Operation .10-12 Heating Mode 10 Cooling Mode .10 Continuous Blower Mode .10 Heat Pump Mode .10-12 Start-up Procedures .12 Adjustments .12-15 Set Gas Input Rate 12-13 Set Temperature Rise 14 Set Thermostat Anticipator .15 Check Safety Controls 15 Checklist 15 SAFETY CONSIDERATIONS Installing and servicing heating equipment can be hazardous due to gas and electrical components.

Only trained and qualified personnel should install, repair, or service heating equipment. Untrained personnel can perform basic maintenance functions such as cleaning and replacing air filters. All other operations must be performed by trained service personnel. When working on heating equipment, observe precautions in the literature, on tags, and on labels attached to or shipped with the unit and other safety precautions that may apply. Table 1–Clearances From Combustible Materials (In.) UNIT SIZE 050 AND 070 096-135 DOWNFLOW (In Alcove or Closet) Single-Wall Vent 1 0 Type B-1 Double-Wall Vent Single-Wall Vent 6 6 Type B-1 Double-Wall Vent 3 3 Single-Wall Vent 6 6 Type B-1 Double-Wall Vent 1 1 HORIZONTAL (Attic, Alcove, or Crawlspace) Single-Wall Vent 1 1 Type B-1 Double-Wall Vent 1 1 Single-Wall Vent 6 6 Type B-1 Double-Wall Vent 3 3 Single-Wall Vent 6 6 Type B-1 Double-Wall Vent 1 1 HORIZONTAL (In Closet) 1 1 0 0 Single-Wall Vent 2 2 Type B-1 Double-Wall Vent Single-Wall Vent 6 6 Type B-1 Double-Wall Vent 3 3 Single-Wall Vent 6 6 Type B-1 Double-Wall Vent 1 1 Sides Back Top Front Vent Sides * Back Top Front Vent Sides * Back Top Front Vent * Indicates supply or return sides when furnace is in the horizontal position. Clearance shown is for outlet end. The inlet end must maintain 6-in. minimum clearance from the vent to combustible materials when using single-wall vent. Minimum 18-in. front clearance required for alcove. NOTES: 1. Provide 30-in. front clearance for servicing. An open door in front of the furnace can meet this requirement. 2. A minimum clearance of 3 in. must be provided in front of the furnace for combustion air and proper operation. 3. Line contact is permitted as shown in Fig. 7. Follow all safety codes. In the United States, follow all safety codes including the National Fuel Gas Code (NFGC) NFPA No. 54-1992/ANSI Z223.1-1992. In Canada, refer to the current Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. Book